45° ICF Hanger Insert Plate

The 45o ICF Hanger Insert Plate is the same as the standard ICF Hanger Insert Plate but gives a solid floor connection for the inside 90o corners as well as 45o corner connections.

Code: #HIP-45


Retrofit Bracket

The Retrofit Bracket is used in conjunction with the Stamped Bearing Bracket as an afterthought for attachment to the concrete. This corrects mistakes made from improper installation of the ICF Hanger Insert Plates.
Code: #ICFRFB 


ICF Hanger System

ICF Hanger System  is used for connecting wood floor joists or for a wood roof connection system. An inexpensive, yet labor friendly connection system.
Above Shot-lightented

T-Form Support Brackets

The T-Form Support Brackets aid installers in constructing a simplified T-form joint from scratch when an actual T-form product is not present on-site. 


Transition Bracket

The Transition Bracket allows two different form widths to be connected together. Primary use is to create a ledge to support brick or a floor system.
Code: #TRA-BR



The V-Clip is used to connect a NUDURA panel to a concrete floor. It allows the contractor to support the panel without additional materials used on the outside of the wall.
Code: #VCLIP

Vertical Joint Clip

The Vertical Joint Clip is designed to connect the form together at the vertical joints. It replaces having to tie wire or tape forms together while providing a solid connection using minimal amount of labor to install.
Code: #VJC

Brick Ties

Cast-In Place Brick Tie and Pintle, enables solid anchorage of veneer masonry through exterior foam to concrete core; tested to meet ASTM D754 (USA) and CSA--A370 (CAN) std. requirements for masonry anchors.

Mount Ties (A) / Pintle (B)

Surface Mount Tie and Pintle, designed to be fastened with 2 NUDURA Hex Head Screws anywhere on the NUDURA fastening strip. This tie will accept NUDURA Pintels and other smaller dimension panels.


Fiber Tape

Fiber Tape is used to provide additional EPS support for field cut forms that have more than 4" (100mm) of EPS extending past the last web, brick ledge forms in the corner conditions and radius panel.
Code: #TAPE

Foam Gun

The Econo Gun II and Sure Shooter Foam Guns are compatible with the NUDURA Low Expansion Foam 24oz (680kg) cans. The NUDURA Low Expansion Foam can be used for a number of different tasks on site.
Code: #GUN-M / GUN  

NUDURA Low Expansion Foam

The Low Expansion Foam is compatible with NUDURA's Expanded Polystyrene (EPS) foam and can be used for a number of different tasks on site including foaming the forms to the slab or footing, between vertical joints, securing service penetrations and as insulation around openings.
Code: #FOAM


4" (102mm) Heavy Duty Tape

The 4" (100mm) Heavy Duty Tape is used for covering the interlock at the top of a wall to prevent concrete from flowing into the sockets. Heavy Duty Tape can also be used as an air barrier tape.
Code: #TAP4HD


Foam Gun Cleaner

The Foam Gun Cleaner is used to clean the internal chamber of the foam gun from any hardened foam. Also used on the external surfaces for cleaning the guns. 
Code: #FOAM-C

4" (100mm) Protective Tape

The 4" (100mm) Protective Tape is used for covering the interlock at the top of a wall to prevent concrete from flowing into the sockets. Protective Tape can also be used as an air barrier tape.
Code: #TAPE-4



Rebar Bender Cutter

The Rebar Cutter is used for cutting and bending reinforcing steel used in the NUDURA wall system. Comes with two cutting heads that will cut up to #5 (15M) reinforcing steel. The rollers used for bending the steel are capable of handling up to a #5 (15M) bar.
Code: #RBC

Easy Buck

The Easy Buck is used for window and door jams and allow nominal sized lumber to fit between the Expanded Polystyrene (EPS) panels. Primary uses for doors and windows. Each bundle contains 100' (30 m) of Easy buck.
Code: #WBUCK

Waterproofing Membrane

The Peel & Stick Waterproofing Membrane is used for below grade damp proofing of the NUDURA walls. Other uses for the Waterproofing Membrane include drain flashings around window and door openings and brick ledge through wall flashings.


4-Way Web Connector

The 4-Way Web Connector allows two or more insert webs to be connected together and used with the panel system to create wider form sizes. It also can be used to create forms of different shapes and sizes. Increased design flexibility.
Code: 4XWEBC


Fiber Mesh

The Fiber Mesh gets embedded into the parge coat to give it strength.
Code: #MESH


Membrane Primer

The Membrane Primer is designed for use with NUDURA's self-adhesive waterproof membranes. This polymer emulsion-based primer is available in a 19L (5 gallon) pail, with a coverage of approximately 650-2000 ft2 (60-190m2) of wall area per pail. The NUDURA Membrane Primer can help improve adhesion of NUDURA's Waterproofing Membrane in specific areas.


Hex Head Screw w/ Washer

The #10 screw can be used to connect the NUDURA Alignment System to the forms. Other uses include attachment of strapping or buck material to concrete. Available in 2" (50mm), 2 1/2" (64mm) and 3" (76mm) lengths. Two 1/4" (6mm) nut drivers included per pail.
Code: #SC-2.0 / SC-2.5 / SC-3.0

10 Piece Bit Kit

Ten piece kits include five 1/4" (6mm) magnetic nutsetters which can be used with any of NUDURA's Hex Head Screws with Steel Flat Washers, as well as five #2 red square driver bits. The durable plastic case keeps all the bits together in one convenient spot and limits trying to find driver bits on site during construction.
Contact your local distributor for information


Parging Mix

The Parge Mix is a dry cementitious product that is used to cover exposed EPS that is not covered by an exterior finish. Used in conjunction with Fiber Mesh. 
Code: #PARGE 

Bit Kit

The Bit Kit is a 10 piece quick change kit that keeps all the bits together in one convenient spot. The kit includes five 1/4" magnetic nut setters which can be used with any of NUDURA's Hex Head Screws with Steel Flat washers, as well as five #2 red square driver bits. It is available in packages of 12.
Code: #BITKIT 


Folding Saw

The Folding Saw is to ease in the cutting of ICF foam and plastic. This product can be used with any of NUDURA's form units. The saw is compact and folds to fit in pockets or tool bags for ease of transport and convenient storage.
Code: #SAW 


  North America 866-468-6299 International +1 705-726-9499